This document describes design decisions that went into implementing Open vSwitch. While we believe these to be reasonable decisions, it is impossible to predict how Open vSwitch will be used in all environments. Understanding assumptions made by Open vSwitch is critical to a successful deployment. The end of this document contains contact information that can be used to let us know how we can make Open vSwitch more generally useful.
Over time, Open vSwitch has added many knobs that control whether a given controller receives OpenFlow asynchronous messages. This section describes how all of these features interact.
First, a service controller never receives any asynchronous messages unless it changes its misssendlen from the service controller default of zero in one of the following ways:
Sending an OFPTSETCONFIG message with nonzero misssendlen.
Sending any NXTSETASYNCCONFIG message: as a side effect, this message changes the misssendlen to OFPDEFAULTMISSSEND_LEN (128) for service controllers.
Second, OFPTFLOWREMOVED and NXTFLOWREMOVED messages are generated only if the flow that was removed had the OFPFFSENDFLOW_REM flag set.
Third, OFPTPACKETIN and NXTPACKETIN messages are sent only to OpenFlow controller connections that have the correct connection ID (see "struct nxcontrollerid" and "struct nxactioncontroller"):
For packet-in messages generated by a NXAST_CONTROLLER action, the controller ID specified in the action.
For other packet-in messages, controller ID zero. (This is the default ID when an OpenFlow controller does not configure one.)
Finally, Open vSwitch consults a per-connection table indexed by the message type, reason code, and current role. The following table shows how this table is initialized by default when an OpenFlow connection is made. An entry labeled "yes" means that the message is sent, an entry labeled "---" means that the message is suppressed.
``` master/ message and reason code other slave ---------------------------------------- ------- ----- OFPTPACKETIN / NXTPACKETIN OFPRNOMATCH yes --- OFPRACTION yes --- OFPRINVALIDTTL --- --- OFPRACTIONSET (OF1.4+) yes --- OFPRGROUP (OF1.4+) yes ---
OFPTFLOWREMOVED / NXTFLOWREMOVED OFPRRIDLETIMEOUT yes --- OFPRRHARDTIMEOUT yes --- OFPRRDELETE yes --- OFPRRGROUPDELETE (OF1.4+) yes --- OFPRRMETERDELETE (OF1.4+) yes --- OFPRREVICTION (OF1.4+) yes ---
OFPTPORTSTATUS OFPPRADD yes yes OFPPRDELETE yes yes OFPPR_MODIFY yes yes
OFPTROLEREQUEST / OFPTROLEREPLY (OF1.4+) OFPCRRMASTERREQUEST --- --- OFPCRRCONFIG --- --- OFPCRREXPERIMENTER --- ---
OFPTTABLESTATUS (OF1.4+) OFPTRVACANCYDOWN --- --- OFPTRVACANCYUP --- ---
OFPTREQUESTFORWARD (OF1.4+) OFPRFRGROUPMOD --- --- OFPRFRMETER_MOD --- --- ```
The NXTSETASYNCCONFIG message directly sets all of the values in this table for the current connection. The OFPCINVALIDTTLTOCONTROLLER bit in the OFPTSETCONFIG message controls the setting for OFPRINVALID_TTL for the "master" role.
The OpenFlow 1.0 specification requires the output port of the OFPATENQUEUE action to "refer to a valid physical port (i.e. < OFPPMAX) or OFPPINPORT". Although OFPPLOCAL is not less than OFPPMAX, it is an 'internal' port which can have QoS applied to it in Linux. Since we allow the OFPATENQUEUE to apply to 'internal' ports whose port numbers are less than OFPPMAX, we interpret OFPPLOCAL as a physical port and support OFPATENQUEUE on it as well.
The OpenFlow specification for the behavior of OFPTFLOWMOD is confusing. The following tables summarize the Open vSwitch implementation of its behavior in the following categories:
"match on priority": Whether the flowmod acts only on flows whose priority matches that included in the flowmod message.
"match on outport": Whether the flowmod acts only on flows that output to the outport included in the flowmod message (if outport is not OFPPNONE). OpenFlow 1.1 and later have a similar feature (not listed separately here) for out_group.
"match on flowcookie": Whether the flowmod acts only on flows whose flow_cookie matches an optional controller-specified value and mask.
"updates flowcookie": Whether the flowmod changes the flowcookie of the flow or flows that it matches to the flowcookie included in the flow_mod message.
"updates OFPFF_ flags": Whether the flowmod changes the OFPFFSENDFLOWREM flag of the flow or flows that it matches to the setting included in the flags of the flow_mod message.
"honors OFPFFCHECKOVERLAP": Whether the OFPFFCHECKOVERLAP flag in the flow_mod is significant.
"updates idletimeout" and "updates hardtimeout": Whether the idletimeout and hardtimeout in the flowmod, respectively, have an effect on the flow or flows matched by the flowmod.
"updates idle timer": Whether the flow_mod resets the per-flow timer that measures how long a flow has been idle.
"updates hard timer": Whether the flow_mod resets the per-flow timer that measures how long it has been since a flow was modified.
"zeros counters": Whether the flow_mod resets per-flow packet and byte counters to zero.
"may add a new flow": Whether the flow_mod may add a new flow to the flow table. (Obviously this is always true for "add" commands but in some OpenFlow versions "modify" and "modify-strict" can also add new flows.)
"sends flowremoved message": Whether the flowmod generates a flow_removed message for the flow or flows that it affects.
An entry labeled "yes" means that the flow mod type does have the indicated behavior, "---" means that it does not, an empty cell means that the property is not applicable, and other values are explained below the table.
``` MODIFY DELETE ADD MODIFY STRICT DELETE STRICT === ====== ====== ====== ====== match on priority yes --- yes --- yes match on outport --- --- --- yes yes match on flowcookie --- --- --- --- --- match on tableid --- --- --- --- --- controller chooses tableid --- --- --- updates flowcookie yes yes yes updates OFPFFSENDFLOWREM yes + + honors OFPFFCHECKOVERLAP yes + + updates idletimeout yes + + updates hardtimeout yes + + resets idle timer yes + + resets hard timer yes yes yes zeros counters yes + + may add a new flow yes yes yes sends flow_removed message --- --- --- % %
(+) "modify" and "modify-strict" only take these actions when they create a new flow, not when they update an existing flow.
(%) "delete" and "deletestrict" generates a flowremoved message if the deleted flow or flows have the OFPFFSENDFLOW_REM flag set. (Each controller can separately control whether it wants to receive the generated messages.) ```
OpenFlow 1.1 makes these changes:
The controller now must specify the tableid of the flow match searched and into which a flow may be inserted. Behavior for a tableid of 255 is undefined.
A flowmod, except an "add", can now match on the flowcookie.
When a flowmod matches on the flowcookie, "modify" and "modify-strict" never insert a new flow.
``` MODIFY DELETE ADD MODIFY STRICT DELETE STRICT === ====== ====== ====== ====== match on priority yes --- yes --- yes match on outport --- --- --- yes yes match on flowcookie --- yes yes yes yes match on tableid yes yes yes yes yes controller chooses tableid yes yes yes updates flowcookie yes --- --- updates OFPFFSENDFLOWREM yes + + honors OFPFFCHECKOVERLAP yes + + updates idletimeout yes + + updates hardtimeout yes + + resets idle timer yes + + resets hard timer yes yes yes zeros counters yes + + may add a new flow yes # # sends flow_removed message --- --- --- % %
(+) "modify" and "modify-strict" only take these actions when they create a new flow, not when they update an existing flow.
(%) "delete" and "deletestrict" generates a flowremoved message if the deleted flow or flows have the OFPFFSENDFLOW_REM flag set. (Each controller can separately control whether it wants to receive the generated messages.)
(#) "modify" and "modify-strict" only add a new flow if the flow_mod does not match on any bits of the flow cookie ```
OpenFlow 1.2 makes these changes:
Only "add" commands ever add flows, "modify" and "modify-strict" never do.
A new flag OFPFFRESETCOUNTS now controls whether "modify" and "modify-strict" reset counters, whereas previously they never reset counters (except when they inserted a new flow).
``` MODIFY DELETE ADD MODIFY STRICT DELETE STRICT === ====== ====== ====== ====== match on priority yes --- yes --- yes match on outport --- --- --- yes yes match on flowcookie --- yes yes yes yes match on tableid yes yes yes yes yes controller chooses tableid yes yes yes updates flowcookie yes --- --- updates OFPFFSENDFLOWREM yes --- --- honors OFPFFCHECKOVERLAP yes --- --- updates idletimeout yes --- --- updates hardtimeout yes --- --- resets idle timer yes --- --- resets hard timer yes yes yes zeros counters yes & & may add a new flow yes --- --- sends flow_removed message --- --- --- % %
(%) "delete" and "deletestrict" generates a flowremoved message if the deleted flow or flows have the OFPFFSENDFLOW_REM flag set. (Each controller can separately control whether it wants to receive the generated messages.)
(&) "modify" and "modify-strict" reset counters if the OFPFFRESETCOUNTS flag is specified. ```
OpenFlow 1.3 makes these changes:
Behavior for a tableid of 255 is now defined, for "delete" and "delete-strict" commands, as meaning to delete from all tables. A tableid of 255 is now explicitly invalid for other commands.
New flags OFPFFNOPKTCOUNTS and OFPFFNOBYTCOUNTS for "add" operations.
The table for 1.3 is the same as the one shown above for 1.2.
OpenFlow 1.4 makes these changes:
Adds the "importance" field to flowmods, but it does not explicitly specify which kinds of flowmods set the importance. For consistency, Open vSwitch uses the same rule for importance as for idletimeout and hardtimeout, that is, only an "ADD" flow_mod sets the importance. (This issue has been filed with the ONF as EXT-496.)
Eviction Mechanism to automatically delete entries of lower importance to make space for newer entries.
Open vSwitch makes all flow table modifications atomically, i.e., any datapath packet only sees flow table configurations either before or after any change made by any flowmod. For example, if a controller removes all flows with a single OpenFlow "flowmod", no packet sees an intermediate version of the OpenFlow pipeline where only some of the flows have been deleted.
It should be noted that Open vSwitch caches datapath flows, and that the cached flows are NOT flushed immediately when a flow table changes. Instead, the datapath flows are revalidated against the new flow table as soon as possible, and usually within one second of the modification. This design amortizes the cost of datapath cache flushing across multiple flow table changes, and has a significant performance effect during simultaneous heavy flow table churn and high traffic load. This means that different cached datapath flows may have been computed based on a different flow table configurations, but each of the datapath flows is guaranteed to have been computed over a coherent view of the flow tables, as described above.
With OpenFlow 1.4 bundles this atomicity can be extended across an arbitrary set of flowmods. Bundles are supported for flowmod and portmod messages only. For flowmods, both 'atomic' and 'ordered' bundle flags are trivially supported, as all bundled messages are executed in the order they were added and all flow table modifications are now atomic to the datapath. Port mods may not appear in atomic bundles, as port status modifications are not atomic.
To support bundles, ovs-ofctl has a '--bundle' option that makes the flow mod commands ('add-flow', 'add-flows', 'mod-flows', 'del-flows', and 'replace-flows') use an OpenFlow 1.4 bundle to operate the modifications as a single atomic transaction. If any of the flow mods in a transaction fail, none of them are executed. All flow mods in a bundle appear to datapath lookups simultaneously.
Furthermore, ovs-ofctl 'add-flow' and 'add-flows' commands now accept arbitrary flow mods as an input by allowing the flow specification to start with an explicit 'add', 'modify', 'modifystrict', 'delete', or 'deletestrict' keyword. A missing keyword is treated as 'add', so this is fully backwards compatible. With the new '--bundle' option all the flow mods are executed as a single atomic transaction using an OpenFlow 1.4 bundle. Without the '--bundle' option the flow mods are executed in order up to the first failing flowmod, and in case of an error the earlier successful flowmods are not rolled back.
The OpenFlow 1.1 specification for OFPTPACKETIN is confusing. The definition in OF1.1 openflow.h is[*]:
/* Packet received on port (datapath -> controller). */
struct ofp_packet_in {
struct ofp_header header;
uint32_t buffer_id; /* ID assigned by datapath. */
uint32_t in_port; /* Port on which frame was received. */
uint32_t in_phy_port; /* Physical Port on which frame was received. */
uint16_t total_len; /* Full length of frame. */
uint8_t reason; /* Reason packet is being sent (one of OFPR_*) */
uint8_t table_id; /* ID of the table that was looked up */
uint8_t data[0]; /* Ethernet frame, halfway through 32-bit word,
so the IP header is 32-bit aligned. The
amount of data is inferred from the length
field in the header. Because of padding,
offsetof(struct ofp_packet_in, data) ==
sizeof(struct ofp_packet_in) - 2. */
};
OFP_ASSERT(sizeof(struct ofp_packet_in) == 24);
The confusing part is the comment on the data[] member. This comment is a leftover from OF1.0 openflow.h, in which the comment was correct: sizeof(struct ofppacketin) is 20 in OF1.0 and offsetof(struct ofppacketin, data) is 18. When OF1.1 was written, the structure members were changed but the comment was carelessly not updated, and the comment became wrong: sizeof(struct ofppacketin) and offsetof(struct ofppacketin, data) are both 24 in OF1.1.
That leaves the question of how to implement ofppacketin in OF1.1. The OpenFlow reference implementation for OF1.1 does not include any padding, that is, the first byte of the encapsulated frame immediately follows the 'table_id' member without a gap. Open vSwitch therefore implements it the same way for compatibility.
For an earlier discussion, please see the thread archived at: https://mailman.stanford.edu/pipermail/openflow-discuss/2011-August/002604.html
[*] The quoted definition is directly from OF1.1. Definitions used inside OVS omit the 8-byte ofp_header members, so the sizes in this discussion are 8 bytes larger than those declared in OVS header files.
The 802.1Q VLAN header causes more trouble than any other 4 bytes in networking. More specifically, three versions of OpenFlow and Open vSwitch have among them four different ways to match the contents and presence of the VLAN header. The following table describes how each version works.
Match NXM OF1.0 OF1.1 OF1.2
----- --------- ----------- ----------- ------------
[1] 0000/0000 ????/1,??/? ????/1,??/? 0000/0000,--
[2] 0000/ffff ffff/0,??/? ffff/0,??/? 0000/ffff,--
[3] 1xxx/1fff 0xxx/0,??/1 0xxx/0,??/1 1xxx/ffff,--
[4] z000/f000 ????/1,0y/0 fffe/0,0y/0 1000/1000,0y
[5] zxxx/ffff 0xxx/0,0y/0 0xxx/0,0y/0 1xxx/ffff,0y
[6] 0000/0fff <none> <none> <none>
[7] 0000/f000 <none> <none> <none>
[8] 0000/efff <none> <none> <none>
[9] 1001/1001 <none> <none> 1001/1001,--
[10] 3000/3000 <none> <none> <none>
Each column is interpreted as follows.
Match: See the list below.
NXM: xxxx/yyyy means NXMOFVLANTCIW with value xxxx and mask yyyy. A mask of 0000 is equivalent to omitting NXMOFVLANTCI(W), a mask of ffff is equivalent to NXMOFVLAN_TCI.
OF1.0 and OF1.1: wwww/x,yy/z means dlvlan wwww, OFPFWDLVLAN x,
dlvlanpcp yy, and OFPFWDLVLANPCP z. If OFPFWDLVLAN or
OFPFWDLVLAN_PCP is 1, the corresponding field value is
wildcarded, otherwise it is matched. ? means that the given bits
are ignored (their conventional values are 0000/x,00/0 in OF1.0,
0000/x,00/1 in OF1.1; x is never ignored).
OF1.2: xxxx/yyyy,zz means OXMOFVLANVIDW with value xxxx and
mask yyyy, and OXMOFVLANPCP (which is not maskable) with
value zz. A mask of 0000 is equivalent to omitting
OXMOFVLANVID(W), a mask of ffff is equivalent to
OXMOFVLANVID. -- means that OXMOFVLAN_PCP is omitted.
The matches are:
[1] Matches any packet, that is, one without an 802.1Q header or with an 802.1Q header with any TCI value.
[2] Matches only packets without an 802.1Q header.
NXM: Any match with (vlan_tci == 0) and (vlan_tci_mask & 0x1000)
!= 0 is equivalent to the one listed in the table.
OF1.0: The spec doesn't define behavior if dl_vlan is set to
0xffff and OFPFW_DL_VLAN_PCP is not set.
OF1.1: The spec says explicitly to ignore dl_vlan_pcp when
dl_vlan is set to 0xffff.
OF1.2: The spec doesn't say what should happen if (vlan_vid == 0)
and (vlan_vid_mask & 0x1000) != 0 but (vlan_vid_mask != 0x1000),
but it would be straightforward to also interpret as [2].
[3] Matches only packets that have an 802.1Q header with VID xxx (and any PCP).
[4] Matches only packets that have an 802.1Q header with PCP y (and any VID).
NXM: z is ((y << 1) | 1).
OF1.0: The spec isn't very clear, but OVS implements it this way.
OF1.2: Presumably other masks such that (vlan_vid_mask & 0x1fff)
== 0x1000 would also work, but the spec doesn't define their
behavior.
[5] Matches only packets that have an 802.1Q header with VID xxx and PCP y.
NXM: z is ((y << 1) | 1).
OF1.2: Presumably other masks such that (vlan_vid_mask & 0x1fff)
== 0x1fff would also work.
[6] Matches packets with no 802.1Q header or with an 802.1Q header with a VID of 0. Only possible with NXM.
[7] Matches packets with no 802.1Q header or with an 802.1Q header with a PCP of 0. Only possible with NXM.
[8] Matches packets with no 802.1Q header or with an 802.1Q header with both VID and PCP of 0. Only possible with NXM.
[9] Matches only packets that have an 802.1Q header with an odd-numbered VID (and any PCP). Only possible with NXM and OF1.2. (This is just an example; one can match on any desired VID bit pattern.)
[10] Matches only packets that have an 802.1Q header with an odd-numbered PCP (and any VID). Only possible with NXM. (This is just an example; one can match on any desired VID bit pattern.)
Additional notes:
OpenFlow 1.0 and later versions have the concept of a "flow cookie", which is a 64-bit integer value attached to each flow. The treatment of the flow cookie has varied greatly across OpenFlow versions, however.
In OpenFlow 1.0:
OFPFC_ADD set the cookie in the flow that it added.
OFPFCMODIFY and OFPFCMODIFY_STRICT updated the cookie for the flow or flows that it modified.
OFPST_FLOW messages included the flow cookie.
OFPTFLOWREMOVED messages reported the cookie of the flow that was removed.
OpenFlow 1.1 made the following changes:
Flow mod operations OFPFCMODIFY, OFPFCMODIFYSTRICT, OFPFCDELETE, and OFPFCDELETESTRICT, plus flow stats requests and aggregate stats requests, gained the ability to match on flow cookies with an arbitrary mask.
OFPFCMODIFY and OFPFCMODIFY_STRICT were changed to add a new flow, in the case of no match, only if the flow table modification operation did not match on the cookie field. (In OpenFlow 1.0, modify operations always added a new flow when there was no match.)
OFPFCMODIFY and OFPFCMODIFY_STRICT no longer updated flow cookies.
OpenFlow 1.2 made the following changes:
Open vSwitch support for OpenFlow 1.0 implements the OpenFlow 1.0 behavior with the following extensions:
An NXM extension field NXMNXCOOKIE(W) allows the NXM versions of OFPFCMODIFY, OFPFCMODIFYSTRICT, OFPFCDELETE, and OFPFCDELETESTRICT flowmods, plus flow stats requests and aggregate stats requests, to match on flow cookies with arbitrary masks. This is much like the equivalent OpenFlow 1.1 feature.
Like OpenFlow 1.1, OFPCMODIFY and OFPFCMODIFY_STRICT add a new flow if there is no match and the mask is zero (or not given).
The "cookie" field in OFPTFLOWMOD and NXTFLOWMOD messages is used as the cookie value for OFPFCADD commands, as described in OpenFlow 1.0. For OFPFCMODIFY and OFPFCMODIFYSTRICT commands, the "cookie" field is used as a new cookie for flows that match unless it is UINT64_MAX, in which case the flow's cookie is not updated.
NXTPACKETIN (the Nicira extended version of OFPTPACKETIN) reports the cookie of the rule that generated the packet, or all-1-bits if no rule generated the packet. (Older versions of OVS used all-0-bits instead of all-1-bits.)
The following table shows the handling of different protocols when receiving OFPFCMODIFY and OFPFCMODIFYSTRICT messages. A mask of 0 indicates either an explicit mask of zero or an implicit one by not specifying the NXMNXCOOKIE(W) field.
```
Match Update Add on miss Add on miss
cookie cookie mask!=0 mask==0
====== ====== =========== ===========
OpenFlow 1.0 no yes
OpenFlow 1.0 has only rudimentary support for multiple flow tables. Notably, OpenFlow 1.0 does not allow the controller to specify the flow table to which a flow is to be added. Open vSwitch adds an extension for this purpose, which is enabled on a per-OpenFlow connection basis using the NXTFLOWMODTABLEID message. When the extension is enabled, the upper 8 bits of the 'command' member in an OFPTFLOWMOD or NXTFLOWMOD message designates the table to which a flow is to be added.
The Open vSwitch software switch implementation offers 255 flow tables. On packet ingress, only the first flow table (table 0) is searched, and the contents of the remaining tables are not considered in any way. Tables other than table 0 only come into play when an NXASTRESUBMITTABLE action specifies another table to search.
Tables 128 and above are reserved for use by the switch itself. Controllers should use only tables 0 through 127.
This section covers the history of the OFPTC_* table configuration bits across OpenFlow versions.
OpenFlow 1.0 flow tables had fixed configurations.
OpenFlow 1.1 enabled controllers to configure behavior upon flow table miss and added the OFPTCMISS* constants for that purpose. OFPTC* did not control anything else but it was nevertheless conceptualized as a set of bit-fields instead of an enum. OF1.1 added the OFPTTABLEMOD message to set OFPTCMISS* for a flow table and added the 'config' field to the OFPSTTABLE reply to report the current setting.
OpenFlow 1.2 did not change anything in this regard.
OpenFlow 1.3 switched to another means to changing flow table miss behavior and deprecated OFPTCMISS* without adding any more OFPTC* constants. This meant that OFPTTABLEMOD now had no purpose at all, but OF1.3 kept it around "for backward compatibility with older and newer versions of the specification." At the same time, OF1.3 introduced a new message OFPMPTABLEFEATURES that included a field 'config' documented as reporting the OFPTC* values set with OFPTTABLEMOD; of course this served no real purpose because no OFPTC* values are defined. OF1.3 did remove the OFPTC* field from OFPMPTABLE (previously named OFPSTTABLE).
OpenFlow 1.4 defined two new OFPTC* constants, OFPTCEVICTION and OFPTCVACANCYEVENTS, using bits that did not overlap with OFPTCMISS* even though those bits had not been defined since OF1.2. OFPTTABLEMOD still controlled these settings. The field for OFPTC* values in OFPMPTABLEFEATURES was renamed from 'config' to 'capabilities' and documented as reporting the flags that are supported in a OFPTTABLEMOD message. The OFPMPTABLEDESC message newly added in OF1.4 reported the OFPTC* setting.
OpenFlow 1.5 did not change anything in this regard.
The following table summarizes. The columns say:
OpenFlow version(s).
The OFPTC_* flags defined in those versions.
Whether OFPTTABLEMOD can modify OFPTC_* flags.
Whether OFPSTTABLE/OFPMPTABLE reports the OFPTC_* flags.
What OFPMPTABLEFEATURES reports (if it exists): either the current configuration or the switch's capabilities.
Whether OFPMPTABLEDESC reports the current configuration.
OpenFlow OFPTC* flags TABLEMOD stats? TABLEFEATURES TABLEDESC
OF1.0 none no[][+] no[] nothing[][+] no[][+] OF1.1/1.2 MISS* yes yes nothing[+] no[+] OF1.3 none yes[*] no[*] config[*] no[*][+] OF1.4/1.5 EVICTION/VACANCYEVENTS yes no capabilities yes
[*] Nothing to report/change anyway.
[+] No such message.
Open vSwitch supports stateless handling of IPv6 packets. Flows can be written to support matching TCP, UDP, and ICMPv6 headers within an IPv6 packet. Deeper matching of some Neighbor Discovery messages is also supported.
IPv6 was not designed to interact well with middle-boxes. This, combined with Open vSwitch's stateless nature, have affected the processing of IPv6 traffic, which is detailed below.
The base IPv6 header is incredibly simple with the intention of only containing information relevant for routing packets between two endpoints. IPv6 relies heavily on the use of extension headers to provide any other functionality. Unfortunately, the extension headers were designed in such a way that it is impossible to move to the next header (including the layer-4 payload) unless the current header is understood.
Open vSwitch will process the following extension headers and continue to the next header:
When a header is encountered that is not in that list, it is considered "terminal". A terminal header's IPv6 protocol value is stored in "nw_proto" for matching purposes. If a terminal header is TCP, UDP, or ICMPv6, the packet will be further processed in an attempt to extract layer-4 information.
IPv6 requires that every link in the internet have an MTU of 1280 octets or greater (RFC 2460). As such, a terminal header (as described above in "Extension Headers") in the first fragment should generally be reachable. In this case, the terminal header's IPv6 protocol type is stored in the "nwproto" field for matching purposes. If a terminal header cannot be found in the first fragment (one with a fragment offset of zero), the "nwproto" field is set to 0. Subsequent fragments (those with a non-zero fragment offset) have the "nw_proto" field set to the IPv6 protocol type for fragments (44).
An IPv6 jumbogram (RFC 2675) is a packet containing a payload longer than 65,535 octets. A jumbogram is only relevant in subnets with a link MTU greater than 65,575 octets, and are not required to be supported on nodes that do not connect to link with such large MTUs. Currently, Open vSwitch doesn't process jumbograms.
An OpenFlow switch must establish and maintain a TCP network connection to its controller. There are two basic ways to categorize the network that this connection traverses: either it is completely separate from the one that the switch is otherwise controlling, or its path may overlap the network that the switch controls. We call the former case "out-of-band control", the latter case "in-band control".
Out-of-band control has the following benefits:
Simplicity: Out-of-band control slightly simplifies the switch implementation.
Reliability: Excessive switch traffic volume cannot interfere with control traffic.
Integrity: Machines not on the control network cannot impersonate a switch or a controller.
Confidentiality: Machines not on the control network cannot snoop on control traffic.
In-band control, on the other hand, has the following advantages:
No dedicated port: There is no need to dedicate a physical switch port to control, which is important on switches that have few ports (e.g. wireless routers, low-end embedded platforms).
No dedicated network: There is no need to build and maintain a separate control network. This is important in many environments because it reduces proliferation of switches and wiring.
Open vSwitch supports both out-of-band and in-band control. This section describes the principles behind in-band control. See the description of the Controller table in ovs-vswitchd.conf.db(5) to configure OVS for in-band control.
The fundamental principle of in-band control is that an OpenFlow switch must recognize and switch control traffic without involving the OpenFlow controller. All the details of implementing in-band control are special cases of this principle.
The rationale for this principle is simple. If the switch does not handle in-band control traffic itself, then it will be caught in a contradiction: it must contact the controller, but it cannot, because only the controller can set up the flows that are needed to contact the controller.
The following points describe important special cases of this principle.
In-band control must be implemented regardless of whether the switch is connected.
It is tempting to implement the in-band control rules only when the switch is not connected to the controller, using the reasoning that the controller should have complete control once it has established a connection with the switch.
This does not work in practice. Consider the case where the switch is connected to the controller. Occasionally it can happen that the controller forgets or otherwise needs to obtain the MAC address of the switch. To do so, the controller sends a broadcast ARP request. A switch that implements the in-band control rules only when it is disconnected will then send an OFPTPACKETIN message up to the controller. The controller will be unable to respond, because it does not know the MAC address of the switch. This is a deadlock situation that can only be resolved by the switch noticing that its connection to the controller has hung and reconnecting.
In-band control must override flows set up by the controller.
It is reasonable to assume that flows set up by the OpenFlow controller should take precedence over in-band control, on the basis that the controller should be in charge of the switch.
Again, this does not work in practice. Reasonable controller implementations may set up a "last resort" fallback rule that wildcards every field and, e.g., sends it up to the controller or discards it. If a controller does that, then it will isolate itself from the switch.
The switch must recognize all control traffic.
The fundamental principle of in-band control states, in part, that a switch must recognize control traffic without involving the OpenFlow controller. More specifically, the switch must recognize all control traffic. "False negatives", that is, packets that constitute control traffic but that the switch does not recognize as control traffic, lead to control traffic storms.
Consider an OpenFlow switch that only recognizes control packets sent to or from that switch. Now suppose that two switches of this type, named A and B, are connected to ports on an Ethernet hub (not a switch) and that an OpenFlow controller is connected to a third hub port. In this setup, control traffic sent by switch A will be seen by switch B, which will send it to the controller as part of an OFPTPACKETIN message. Switch A will then see the OFPTPACKETIN message's packet, re-encapsulate it in another OFPTPACKETIN, and send it to the controller. Switch B will then see that OFPTPACKETIN, and so on in an infinite loop.
Incidentally, the consequences of "false positives", where packets that are not control traffic are nevertheless recognized as control traffic, are much less severe. The controller will not be able to control their behavior, but the network will remain in working order. False positives do constitute a security problem.
The switch should use echo-requests to detect disconnection.
TCP will notice that a connection has hung, but this can take a considerable amount of time. For example, with default settings the Linux kernel TCP implementation will retransmit for between 13 and 30 minutes, depending on the connection's retransmission timeout, according to kernel documentation. This is far too long for a switch to be disconnected, so an OpenFlow switch should implement its own connection timeout. OpenFlow OFPTECHOREQUEST messages are the best way to do this, since they test the OpenFlow connection itself.
This section describes how Open vSwitch implements in-band control. Correctly implementing in-band control has proven difficult due to its many subtleties, and has thus gone through many iterations. Please read through and understand the reasoning behind the chosen rules before making modifications.
Open vSwitch implements in-band control as "hidden" flows, that is, flows that are not visible through OpenFlow, and at a higher priority than wildcarded flows can be set up through OpenFlow. This is done so that the OpenFlow controller cannot interfere with them and possibly break connectivity with its switches. It is possible to see all flows, including in-band ones, with the ovs-appctl "bridge/dump-flows" command.
The Open vSwitch implementation of in-band control can hide traffic to arbitrary "remotes", where each remote is one TCP port on one IP address. Currently the remotes are automatically configured as the in-band OpenFlow controllers plus the OVSDB managers, if any. (The latter is a requirement because OVSDB managers are responsible for configuring OpenFlow controllers, so if the manager cannot be reached then OpenFlow cannot be reconfigured.)
The following rules (with the OFPP_NORMAL action) are set up on any bridge that has any remotes:
(a) DHCP requests sent from the local port. (b) ARP replies to the local port's MAC address. (c) ARP requests from the local port's MAC address.
In-band also sets up the following rules for each unique next-hop MAC address for the remotes' IPs (the "next hop" is either the remote itself, if it is on a local subnet, or the gateway to reach the remote):
(d) ARP replies to the next hop's MAC address. (e) ARP requests from the next hop's MAC address.
In-band also sets up the following rules for each unique remote IP address:
(f) ARP replies containing the remote's IP address as a target. (g) ARP requests containing the remote's IP address as a source.
In-band also sets up the following rules for each unique remote (IP,port) pair:
(h) TCP traffic to the remote's IP and port. (i) TCP traffic from the remote's IP and port.
The goal of these rules is to be as narrow as possible to allow a switch to join a network and be able to communicate with the remotes. As mentioned earlier, these rules have higher priority than the controller's rules, so if they are too broad, they may prevent the controller from implementing its policy. As such, in-band actively monitors some aspects of flow and packet processing so that the rules can be made more precise.
In-band control monitors attempts to add flows into the datapath that could interfere with its duties. The datapath only allows exact match entries, so in-band control is able to be very precise about the flows it prevents. Flows that miss in the datapath are sent to userspace to be processed, so preventing these flows from being cached in the "fast path" does not affect correctness. The only type of flow that is currently prevented is one that would prevent DHCP replies from being seen by the local port. For example, a rule that forwarded all DHCP traffic to the controller would not be allowed, but one that forwarded to all ports (including the local port) would.
As mentioned earlier, packets that miss in the datapath are sent to the userspace for processing. The userspace has its own flow table, the "classifier", so in-band checks whether any special processing is needed before the classifier is consulted. If a packet is a DHCP response to a request from the local port, the packet is forwarded to the local port, regardless of the flow table. Note that this requires L7 processing of DHCP replies to determine whether the 'chaddr' field matches the MAC address of the local port.
It is interesting to note that for an L3-based in-band control mechanism, the majority of rules are devoted to ARP traffic. At first glance, some of these rules appear redundant. However, each serves an important role. First, in order to determine the MAC address of the remote side (controller or gateway) for other ARP rules, we must allow ARP traffic for our local port with rules (b) and (c). If we are between a switch and its connection to the remote, we have to allow the other switch's ARP traffic to through. This is done with rules (d) and (e), since we do not know the addresses of the other switches a priori, but do know the remote's or gateway's. Finally, if the remote is running in a local guest VM that is not reached through the local port, the switch that is connected to the VM must allow ARP traffic based on the remote's IP address, since it will not know the MAC address of the local port that is sending the traffic or the MAC address of the remote in the guest VM.
With a few notable exceptions below, in-band should work in most network setups. The following are considered "supported" in the current implementation:
Locally Connected. The switch and remote are on the same subnet. This uses rules (a), (b), (c), (h), and (i).
Reached through Gateway. The switch and remote are on different subnets and must go through a gateway. This uses rules (a), (b), (c), (h), and (i).
Between Switch and Remote. This switch is between another switch and the remote, and we want to allow the other switch's traffic through. This uses rules (d), (e), (h), and (i). It uses (b) and (c) indirectly in order to know the MAC address for rules (d) and (e). Note that DHCP for the other switch will not work unless an OpenFlow controller explicitly lets this switch pass the traffic.
Between Switch and Gateway. This switch is between another switch and the gateway, and we want to allow the other switch's traffic through. This uses the same rules and logic as the "Between Switch and Remote" configuration described earlier.
Remote on Local VM. The remote is a guest VM on the system running in-band control. This uses rules (a), (b), (c), (h), and (i).
Remote on Local VM with Different Networks. The remote is a guest VM on the system running in-band control, but the local port is not used to connect to the remote. For example, an IP address is configured on eth0 of the switch. The remote's VM is connected through eth1 of the switch, but an IP address has not been configured for that port on the switch. As such, the switch will use eth0 to connect to the remote, and eth1's rules about the local port will not work. In the example, the switch attached to eth0 would use rules (a), (b), (c), (h), and (i) on eth0. The switch attached to eth1 would use rules (f), (g), (h), and (i).
The following are explicitly not supported by in-band control:
Specify Remote by Name. Currently, the remote must be identified by IP address. A naive approach would be to permit all DNS traffic. Unfortunately, this would prevent the controller from defining any policy over DNS. Since switches that are located behind us need to connect to the remote, in-band cannot simply add a rule that allows DNS traffic from the local port. The "correct" way to support this is to parse DNS requests to allow all traffic related to a request for the remote's name through. Due to the potential security problems and amount of processing, we decided to hold off for the time-being.
Differing Remotes for Switches. All switches must know the L3 addresses for all the remotes that other switches may use, since rules need to be set up to allow traffic related to those remotes through. See rules (f), (g), (h), and (i).
Differing Routes for Switches. In order for the switch to allow other switches to connect to a remote through a gateway, it allows the gateway's traffic through with rules (d) and (e). If the routes to the remote differ for the two switches, we will not know the MAC address of the alternate gateway.
It seems likely that many controllers, at least at startup, use the OpenFlow "flow statistics" request to obtain existing flows, then compare the flows' actions against the actions that they expect to find. Before version 1.8.0, Open vSwitch always returned exact, byte-for-byte copies of the actions that had been added to the flow table. The current version of Open vSwitch does not always do this in some exceptional cases. This section lists the exceptions that controller authors must keep in mind if they compare actual actions against desired actions in a bytewise fashion:
Open vSwitch zeros padding bytes in action structures, regardless of their values when the flows were added.
Open vSwitch "normalizes" the instructions in OpenFlow 1.1 (and later) in the following way:
OVS sorts the instructions into the following order: Apply-Actions, Clear-Actions, Write-Actions, Write-Metadata, Goto-Table.
OVS drops Apply-Actions instructions that have empty action lists.
OVS drops Write-Actions instructions that have empty action sets.
Please report other discrepancies, if you notice any, so that we can fix or document them.
Suggestions to improve Open vSwitch are welcome at discuss@openvswitch.org.